HOME > TIRO/SHOOTING > OTTIMIZZAZIONE DELL'ARMA / RIFLE TUNING ITEMS > CALCIATURE E ACCESSORI / RIFLE STOCKS-CHASSIS AND ACCESSORIES > ACCESSORI PER CHASSIS MPA / ACCESSORIES
Ordina per:
Pagina di 1
MPA SPIGOT MOUNT MPA BAG RIDER
IL NOSTRO PREZZO: €53.00
IL NOSTRO PREZZO: €57.00
MPA SPIGOT MOUNT MPA BAG RIDER

This Spigot Mount is designed to be used with the MPA BA Lite Chassis and or Rifle and our newer BA Chassis and Comp Chassis.. It is installed by removing the picatinny rail from the existing chassis, installing that rail on the spigot mount, sliding into the slot on the face of the Chassis and attaching with the supplied Flat Head Cap Screws. The end user can also install a sling stud into one of the 3 10-32 threaded holes on this mount.

The rail shown is not included. However, the rail that is on the existing chassis will fit this spigot perfectly.

For Standard BA Chassis and Comp chassis, if yours has the oblong slot cut in the front of the fore-end, then it will accept the spigot mount. This change was made in the summer of 2016 to the Standard and Comp Chassis.

This new bag rider design, with the included flush cup, was an idea from Dave Preston, winner of the 2015 PRS Series. The bag rider attaches to your MPA BA Chassis, Comp Chassis or BA Lite Chassis that has a threaded three hole pattern in the bottom of the buttstock body. Its general purpose is to allow a consistent management of recoil when using a rear bag.

The purpose the flush cup, as conceived by Dave, is used when shooting certain positional stances when a sling is used to provide support for the rifle. Have the rear connection point on the bottom of the rifle pulls the rifle downward, as compared to side positioned flush cups which can trend the rifle laterally.

MPA MAG EXTENDER MPA RAT PIC RAIL INSERT
IL NOSTRO PREZZO: €62.00
IL NOSTRO PREZZO: €62.00
MPA MAG EXTENDER MPA RAT PIC RAIL INSERT
MPA Mag Extender is designed for 308 Box magazines built by AICS or Accurate Mag – single feed only. (Will not work with AW Mags). Simply remove the existing floorplate, remove the base insert (from the Accurate Mags only), depress the spring into the mag body, slide the mag extender in place and secure with the included 6-32 set screw. Make sure the mag spring has seated itself flush with the bottom of the mag extender.
Produced from 6061 Aluminum. Cerakote Black and laser engraved.
Increases the magazine capacity to 14 rounds.

MPA EVG GRIP MPA DATA CARD HOLDER
IL NOSTRO PREZZO: €71.00
IL NOSTRO PREZZO: €83.00
MPA EVG GRIP MPA DATA CARD HOLDER

This new injected molded Vertical Grip is designed for the MPA BA Chassis System. The grip design includes a true Vertical interface with the rifle, an Enlarged Palm Swell, Trigger Finger Support Rest and the Enhanced Thumb Notch.

The grip also comes with our special grip tape for improved contact.

The interface with the rifle is a standard A2 type, so the grip, with potential minor modifications, should fit onto other rifles, carbines and chassis that utilize an A2 Grip.

Since the grip is a solid injection molded component, it can be modified without sacrificing the strength and integrity of the part. So if you need to polish, grind, sand or another method of modification, you wont hurt the grip. Just be careful not to remove too much.

This grip will fit on the BA Lite and BA-CZ455 Chassis. However, there will be a slight gap between the thumb notch on the grip and the chassis.

This new Data Card Holder System is designed to be used on any MPA full size chassis (MPA BA Chassis, MPA Comp Chassis) to provide a quick and effective method of viewing your DOPE for target distances while keeping your cheek welded to the cheek riser.

The system attaches to any of the six oblong slots on either side of the magazine well. The system provides multiple methods of removing from the chassis.

  1. Using the included Allen wrench, loosen the set screw in the “Chassis Mount” component and slide the unit out of the oblong slot.
  2. Unscrew the “Wire to Chassis Mount” and remove the entire assembly, less the “Chassis Mount” which will stay attached to the chassis.
  3. Unscrew the Thumb screw that holds the data card in place.

The data card has a surface similar to a dry erase board. You can use either a grease pen, a dry erase pin, or we recommend a “Crayola Washable Marker” which tends to leave the markings in place on the data card even when you make subtle contact with the board (dry erase markers are too easy to rub off). When its time to replace your data, simply wipe off the markings with a cloth or paper towel. The shooter also has the option of putting painters tape on the card and removing when the stage or shooting session is completed.

The data card is designed to be removed by unscrewing the Thumb screw that holds it in place. The card can he oriented top to bottom or left to right. This gives the shooter multiple options for card placement as well as the ability to write the DOPE on the card while not attached to the rifle.

There is also a hole cut into the data card that is designed to hold the allen wrench (5/64) in place while shooting. The wrench has a special treatment performed on the shank to keep it securely in the hole while shooting or moving the rifle.

The wire is flexible and has strong “obedience” (the ability to stay in any position you bend it). It is simple 12 gage solid electrical wire.

MPA ROTATING BARRICADE STOP MPA TRINITY RAIL
IL NOSTRO PREZZO: €98.00
IL NOSTRO PREZZO: €99.00
MPA ROTATING BARRICADE STOP MPA TRINITY RAIL

Use this quick disconnect rotating barricade stop on your
MPA BA Chassis or Rifle with 1/4″ drilled and reamed holes on fore end for a
rock solid setup on a variety of barricades. This is an outstanding accessory
for your BA system to provide a significant competitive advantage during PRS
and similar Long Range Tactical Rifle competitions.



If you have an older BA Rifle or Chassis, with only drilled
and tapped holes on the bottom of the fore end and want to utilize this system,
contact customer service at MPA to have your chassis sent back in for the
necessary modifications.

This Trinity Rail System is designed to be used on any MPA chassis (MPA BA Chassis, MPA Comp Chassis, MPA BA Lite Chassis) to provide an alternate location for positioning a bipod or other picatinny rail attached item. It attaches to the bottom of the fore end of the chassis body via the 2 slots that run the full length of the bottom of the chassis. The system is designed for quick and easy attachment and removal.

It includes the Trinity Rail Base, Short Bipod Picatinny Rail, (4) SHCS and (4) M-lok nuts.

MPA RAT HARRIS BLOCK MPA OFFSET ROTATING BARRICADE STOP
IL NOSTRO PREZZO: €99.00
IL NOSTRO PREZZO: €115.00
MPA RAT HARRIS BLOCK MPA OFFSET ROTATING BARRICADE STOP

This offset barricade stop is designed to be used in PRS and similar long range rifle competitions when using the MPA BA Chassis system. Designed like our standard rotating barricade stop, but with a wider base. The hole location for the quick release clevis pin is in the same location from one surface as our standard stop, but with the additional thickness on the opposite surface, provides the shooter with a wider “pan” capability but rotating the stop between the thick and thin surface.

If you plan on using the BA chassis in tactical, positional long range rifle competitions, this accessory is a “must have.” Once you get it, you will understand…….

MPA RAT BASE ADAPTOR MPA ENHANCED BAG RIDER
IL NOSTRO PREZZO: €115.00
IL NOSTRO PREZZO: €118.00
MPA RAT BASE ADAPTOR MPA ENHANCED BAG RIDER

Our newest Enhanced Bag Rider design was designed for F-Class Shooters, and provides a rock solid rear support when using an appropriate dual ear (or “V”) rear bag, such as the Protektor Series Rabbit Ear Design. It also provides an enhanced level of rear support for all long distance shooters, whether you’re a belly shooter or top level PRS competitor. This design has been successfully used this year at multiple PRS events by Team MPA Shooters.

The stability this rear bag rider provides is incredible, especially when shooting groups. If you’ve ever had some challenges keeping the rifle ultra stable when prone, this accessory will improve performance.

This Enhanced Bag Rider works with all BA, BA Comp and BA lite chassis that have a 3 hole pattern on the bottom of the buttstock.

It comes with a black cerakoted bag rider, 2 set screws, and a turned step shaft designed to be inserted into the monopod slot for installation purposes. The side profile is notched to all use of the bottom flush cup for sling or bag attachment.

MPA STANDARD MONOPOD MPA RAT MAGNETO SPEED ADAPTOR
IL NOSTRO PREZZO: €124.00
IL NOSTRO PREZZO: €124.00
MPA STANDARD MONOPOD MPA RAT MAGNETO SPEED ADAPTOR

This monopod system is designed to work with out Bolt Action Rifles and Chassis Systems.

MPA DLOC HARRIS BIPOD ADAPTOR MPA STUBBY MONOPOD
IL NOSTRO PREZZO: €129.00
IL NOSTRO PREZZO: €129.00
MPA DLOC HARRIS BIPOD ADAPTOR MPA STUBBY MONOPOD

This adaptor will allow your Harris bipod to attach directly to a picatinny rail. Simply remove the Harris sling stud attachment assembly and install this system. The process takes less than 1 minute and allows a quick attach/detach of your Harris bipod from your Mil-Spec 1913 Picatinny Rail.

Includes Adaptor and Knob

This “Stubby” version of our monopod system is designed to work with out Bolt Action Rifles and Chassis Systems.

The Minimum Length of the monopod is 2.875″. This is measured from the base of the monopod to the top of the 2nd thumb wheel.

This system is 1″ shorter than our standard Monopod.

Installation is simple. Just remove the existing monopod from your MPA BA Chassis, use the existing hardware, and re-install the new Stubby Version.

MPA OFFSET CHEEK RISER MPA WEDGE LOCK SYSTEM
IL NOSTRO PREZZO: €129.00
IL NOSTRO PREZZO: €177.00
MPA OFFSET CHEEK RISER MPA WEDGE LOCK SYSTEM

This barricade stop system is designed to be used in PRS and similar long range rifle competitions when using the MPA BA Chassis system.

The system is specifically designed to stabilize your rifle when shooting off cow gates, round fences, round barricades or other cylindrical configurations. One of the most difficult props or stage configurations we shoot in positional competitions are cow gates or other round support surfaces. This system we developed works incredibly well to stabilize your rifle when you encounter one of these .

The system includes (2) modified offset barricade stops and (2) quick release pins.

   
 

 

Copyright ©  www.gac-rifles.com. P.I. IT03358220980.All Rights Reserved. Built with Volusion